How
do I install the quick touch application on LifeBook S series?
A1
By
default, these four quick touch application buttons will be
configured for the following applications:
Notepad
Calculator (Not applicable for
LifeBook B-2130, B-2150 & B-2174)
Internet Browser
Email
Installing Quick Touch Application
1.
Run
setup from the folder /Touch_Button
2.
"Installing Fujitsu
Quick Touch" programme will be launched, click Next and
follow instructions to install the application.
3.
When the setup has
finished, please read the Software Instruction, "Readme
- Notepad" carefully:
Configuring the Quick Touch Applications
4.
To use the Quick
Touch Application, first setup the Quick Touch application
Icon from start menu as shown below.
5.
"(Easy button) configuration"
menu will be launched. The numbered tabs at the top section
represent the respective four quick touch buttons. By
default, the buttons are preset as:
Notepad,
Calculator,
Internet Browser and
Email.
6.
You can reconfigure
the 4 buttons by selecting the numbered tabs which represent
the respective buttons. click on Browse to select the
desired application from your hard drive.
7.
Or alternatively,
you can programmed the button from Start Menu, click on
Browse to select the Applications.
How
do I install the security application on my S-4546 Series LifeBook?
A2
Security
Password, Security Buttons
LifeBook S-4546 Series with Security
Panel offers security function for system boot up and extra
hardware security. The four numeric programmable application
launch buttons can be set as the system boot up password,
more than 800,000 sets of password.
NOTE:
To protect the interest of our customer, please note that the
Supervisor password cannot be removed by any means and by end-user.
Fujitsu reserved the right and do not disclose the system security
code. To remove the Supervisor password, kindly send in your
notebook or contact our warranty helpdesk for arrangement, please
note that the service is chargeable.
My
LifeBook S series seems to overheat quickly. The manual shows
three slots in the back as vents for the fan. My vents are closed
and sealed. The new S series has three openings for the fan
to blow the heat from the unit. Is my unit faulty or has the
new S series been improved?
A3
This model
is designed without a fan because the CPU can take the heat.
The LifeBook incorporates a heat sink feature whereby heat is
conducted to the top of the CPU and dissipated over a surface
area, hence the system feels warm. The user manual shows other
models with similar features where the CPU has less heat sink
on top of the CPU and therefore require a fan to cool down the
system.
I
have a LifeBook S-4510. May I know how to enable the function
that automatically suspends my notebook when I close it, and
resume its previous function when I open the LCD screen? Also
would the CD-R/RW function well if I use Windows XP? Will I
be able to use the same driver & software?
A4
For
this function, please check your 'Power Options' from the 'Control
Panel', and 'Settings'. When the LCD screen is closed, the system
will be suspended or go into 'Hibernate' mode. From the BIOS
under 'Power' section, check that the 'Resume' option is on
when opening the LCD screen.
For the CD/R-RW, no driver is needed
for the CD-R/RW drive when using the default Windows XP 'CD-Recorder'
feature to write on the CD-ROM disk. The CD-R/RW application
bundled with your S-4510 cannot support Windows XP and you
should not attempt to install it. For more information, please
refer to Microsoft's website. In addition, you can go to www.roxio.com
for CD-R/RW application information update.
How
do I upgrade my Adaptec software for LifeBook S-4510?
A5
The
Windows XP version for the Easy Creator is Version 5.1, you
may get it from the website http://www.roxio.com/xpinfo/upgrade4.jhtml.
You may be required to pay online for the upgrade.
I
realise that the application Bay Manager is not compatible with
my LifeBook S-4540. How do I swap devices since my system is
currently using Windows 98?
A6
The
Bay Manager is only supported by Windows 98. In Windows XP,
it has its own built-in features. To perform the swap in Windows
XP, please select the eject icon from the taskbar near the speaker
icon on the right hand corner of the screen. Double click on
the icon. Once the eject button menu pop-up on screen, select
the device you want to eject and select 'OK'. Use the lever
beside the device to remove the device. After that, press the
Sus/Res button to let the system go into 'standby' or 'hibernate'
mode. Plug in the device you wish to use and press the 'Sus/Res'
button again to wake the system up. Now you can use the new
device.
I
am informed by a system warning on my S-4542 that there is an
execution error: "FUJITSU QUICK TOUCH, please use the installation
disk". What disk do I use?
A7
Please
use the Composite or Driver CD to install the Quick Touch Application
again. Afterwhich, use the application to configure your desired
setting for the Quick Touch buttons. The folder containing the
application is S-4542\touch_button\. Click 'Start' select Programs
and select Fujitsu Quick Touch.
What
is the type of video capture device that comes with the LifeBook
S-4562 and the configuration setting for running 'Windows Movie
Maker' on Windows ME?
A8
The
LifeBook S-4562 does not have a built-in video capture device.
You may consider adding the following or use the following devices,
depending on your requirements.
USB Digital Still Picture camera with video clip feature,
which can store and capture short video clips on devices
attached to USB ports, or
Digital Video Picture camera, which can store and capture
video clips on devices attached to IEEE 1394 (Fire wire)
port, or
PCMCIA video capture card.
Movie Maker is an entry-level software with limited functions.
There is a range of video capture software in the market.
Eg. 'Adobe Premier', 'Snazzi', 'Video Studio'.
How
can I switch off the Hibernation/Standby mode on my LifeBook
S-4572?
A9
If
you would like to disable the Hibernation mode, you can go to
'Control Panel' and select 'Power Options'. Select 'Advanced'
and uncheck the check box next to 'Hibernation' to disable the
power management option.
